Apple IIe Motherboard

From The ReActiveMicro Apple II Wiki
Jump to navigation Jump to search
Apple IIe "Rev B" Motherboard, Current Version

The Apple IIe Motherboard project was started on August 12th, 2022 by Henry from ReActiveMicro, and was officially released on , 2022.

This marks the second full computer project released by ReActiveMicro, the first being the Apple II Plus Rev 7 RFI. The concept is a replacement board which is known good and fully tested, to be used as a replacement for the original motherboard.


Product Status: Actively sold by ReActiveMicro.

Support: Post on the Discussion page (link above) or email ReActiveMicro Support.

Sales: Visit the ReActiveMicro Store.


Kit Assembly

The Apple IIe Motherboard Kit is a total of 1517 pads or "solder joints". It takes about 3 hours to fully assemble a kit if you have a decent iron, flux, and solder. The parts included with your kit and the PCB have basic labels. Those with intermediate knowledge should have little trouble assembling the kit from the labels on the parts, the bag, and the PCB. The images below of the motherboards can also be used for reference or to determine orientation, such as the diodes.


To assemble your kit we recommend adding parts in groups and then soldering them. This will be the fastest way to assemble the PCB rather than adding one part at a time then soldering it.

  • Start with the small passive parts like caps and resistors. Some of the location labels will be hard to see if you start with the sockets or other parts. Each time a part is added you can simply bend over a leg on each side to help hold the part to the PCB which allows the board to be turned over and prevents parts from falling out. It is most simple to load all the parts in groups and then solder and clip the legs as needed.
  • A good loupe (magnifying glass) is recommended for helping identify and confirm parts, like the markings on some small caps. It also helps with solder joint inspection. An illuminated 40 x 25mm and a 35 x 50mm loupe are well worth the investment and can be had for about $10 each on eBay.


Resistors

Your kit includes resistors. They should be the less precise "4 band" style which are typically 5% tolerance. You can also use the more precise "5 band" style which are typically 1% tolerance. Here are some charts on how to read them to help make matching locations on your PCB more easy.


Here is a list of resistors on the PCB:
PCB Location Value
R30,R37-38,R73 47 ohms
R1 56 ohms
R8,R40 75 ohms
R16* 75 ohms (2 watts)
R9,R17,R21-24 100 ohms
R41-44 120 ohms
R34-35 150 ohms
R11,R45 200 ohms
R36 270 ohms
R5 330 ohms
R15,R19,R25,R27-R29 1k ohms
R7 2.7k ohms
R10 5.6k ohms
R3,R13 6.8k ohms
R4,R6,R12,R14,R20 12k ohms
R39 47k ohms
R32 100k ohms
R18 1M ohms
*Can be omitted if RM PSU is used.

Related to the resistors are the Resistor Network Arrays. These are the SIP (single inline pin) parts for locations RP1-RP3. Each has a 'dot' on the part and PCB to determine Pin1, which are all toward the keyboard end of the PCB.

Capacitors & Didoes

Note: Cautionary care needs to be taken while installing capacitors and diodes.

If your kit includes Aluminum or Tantalum capacitors, or "caps" for short, then be sure to install them in the correct orientation. The PCB will be clearly marked with "+" signs for all cap locations when the orientation of the part matters, or a polarized part is normally used. Sometimes a non-polarized part is used in place of a polarized one and then its orientation does not matter, however install a polarized cap backwards and you will damage it. An Aluminum Electrolytic will have a strip pointing to the NEGATIVE end lead. A Tantalum Electrolytic will generally have a marking or stripe to denote (not always pointing to) the POSITIVE lead.

Here is a list of capacitors on the PCB:
PCB Location Value
C34-35,C37,C40,C71 22nF, Ceramic Cap
C1-7,10-11,13,16,18-24,26-31,33 100nf, Ceramic Cap
37-39,41-52,55-69,73-76,78-81,83-89 100nf, Ceramic Cap
C70 47pF, Ceramic Cap
C32 47pF, Mica Cap
C25 100pF, Ceramic Cap
C90-93 220pF, Ceramic Cap
C9,C8,C12,C15,C17,C53-54,C72,C82 10uF, Electrolytic Cap
CR4 Diode
CR1, CR2 LED, Red
  • Install the Aluminum caps and be sure to install correctly as they are polarized.
  • All caps will have value markings on them. "106" is 10uF, and "104" is .1uF. 10uF is also typically physically larger than .1uF. "470" is 47pF, "101" is 100pF, and "221" is 220pF for example. This should also help identify the ceramic caps in the kit. They along with the Electrolytic caps can also clearly be seen in the assembled pic above.
  • Be sure to installed the LEDs correctly. One side of the base of the LED will be "flat" compared to the other side. Be sure to align the flat side as noted on the motherboard location marking. This same rule will apply to the transistors as well.

IC Sockets

  • Once the passive parts are installed next should be the IC sockets. When a socket is loaded on the board bending the corner pins of the sockets helps hole it to the PCB which allows group loading and soldering. The sockets are all the same thickness. So if you solder on a flat surface then this will also help hold all the sockets flat to the PCB and give a more uniform appearance when completed. Be sure ALL pin 1 'notches' are facing towards the keyboard end. The CPU socket 'notch' should be towards the Game IO / Video side, and the ROM SPCL should be facing towards the crystal side.
  • End with the larger parts, like jacks, and finally the slots. Don't bend over these parts pins/legs as they will be too hard. You will need to hold them in place as you solder a few pins before you can group solder.