Difference between revisions of "Mockingboard"

From The ReActiveMicro Apple II Wiki
Jump to navigation Jump to search
Line 11: Line 11:
 
Henry had been discussing possible project ideas with Bill Garber.  Bill offered to help show Henry how to use ExpressPCB CAD software, which is what most beginner hobbyists used back in early and mid 2000's.
 
Henry had been discussing possible project ideas with Bill Garber.  Bill offered to help show Henry how to use ExpressPCB CAD software, which is what most beginner hobbyists used back in early and mid 2000's.
  
Henry disassembled the board and noted what all the parts were.  Bill was involved with starting the CAD layout, however he wasn't able to finish, so Henry took over and completed the project.  Bill also helped with updating the deign from an RCA Audio Cable to a 3.5mm Jack.  He is also credited with the concept to add the 3.5mm Jack to the rear side of the IIe, which allows a more simple and shorter cable connection.  Henry is credited with adding the II speaker input jack circuit to the board.
+
Henry disassembled the board and noted what all the parts were.  Bill was involved with starting the CAD layout, however he wasn't able to finish, so Henry took over and completed the project.  Bill also helped with updating the design from an RCA Audio Cable to a 3.5mm Jack.  He is also credited with the concept to add the 3.5mm Jack to the rear side of the IIe, which allows a more simple and shorter cable connection.  Henry is credited with adding the II speaker input jack circuit to the board.
 
 
  
 
== Different Versions of the Cloned Mockingboard == <!--T:3-->
 
== Different Versions of the Cloned Mockingboard == <!--T:3-->

Revision as of 01:37, 15 June 2016

The Mockingboard is a sound card for the Apple II/II+/IIe/IIgs designed originally by Sweet Micro Systems. In 2005 ReActiveMicro (then called GSE-Reactive) was the first company to reproduced a clone of the board called "Mockingboard v1".

Project Status: Complete. In production. Active sold by ReActiveMicro and Ultimate-Micro.com. Project will be superseded by the Phasor project, then discontinued.


History[edit]

The Mockingboard v1 was the first project ReActiveMicro started with in September 2005. After a bit of market research there seemed be enough demand to warrant this project. The board itself also seemed like a good candidate since it was a simple design, 2 layer PCB, and used standard parts which were still easily sourceable. Henry then found the board on eBay and won the auction.

Henry had been discussing possible project ideas with Bill Garber. Bill offered to help show Henry how to use ExpressPCB CAD software, which is what most beginner hobbyists used back in early and mid 2000's.

Henry disassembled the board and noted what all the parts were. Bill was involved with starting the CAD layout, however he wasn't able to finish, so Henry took over and completed the project. Bill also helped with updating the design from an RCA Audio Cable to a 3.5mm Jack. He is also credited with the concept to add the 3.5mm Jack to the rear side of the IIe, which allows a more simple and shorter cable connection. Henry is credited with adding the II speaker input jack circuit to the board.

Different Versions of the Cloned Mockingboard[edit]

Mockingboard v1 from GSE-Reactive

In late 2005 ReActiveMicro (then called GSE-Reactive) produced a clone of the board called "Mockingboard v1". ReActiveMicro sold the Mockingboard v1 in fully assembled, or in user-assessable "kit" form. There were about 50 units produced and sold. The silkscreen shows "GSE-Reactive.com" on the lower front.






Mockingboard v1a from GSE-Reactive

In late 2010 Tom Arnold of philosophyofsound.com approached Henry about making a new run of boards. Tom used the ReActiveMicro design but relabeled it as "Mockingboard v1a". About 40 units were produced. The silkscreen shows "ReactiveMicro.com" on the lower front. Ulitmate-Micro helped distribute these boards via the UltimateApple2.com Store. Tom also sold some units himself.







Mockingboard v1a from GSE-Reactive

Although still called "Mockingboard v1", in 2015 Tom had another batch of boards made, but this later run has the "UM" logo on it and shows "UltimateApple2.com" and "ReActiveMicro.com" on the lower front. About 30 units were produced.


Known Errors In The v1 And v1a Designs[edit]

In 2016 Chris Torrance discovered that the 3.5mm Audio Jack was wired backwards. This is evident all the way back on the GarberStreet schematic (upper right, linked below) of the Mockingboard from 2004.

The Apple II Speaker Input circuit Henry designed was of a lower audio output level than the Mockingboard generated sound effects. Since Mockingboard sounds and Apple II sounds would never be played at the same time, this has never posed much of an issue.

Chris has a few videos that can be found on YouTube addressing the reversed channel issue. Tom Arnold has since devised a work-around mod that Chris demonstrates in his video.

Documentation, Files, and Software[edit]